Read and download CEN-TECH Multimeter 69096 operating instructions manual online. Download free CEN-TECH user manuals, owners manuals, instructions, warranties and installation guides, etc.

Note the main selector wheel on the front of the multimeter. Use this wheel to select the function you need and the sensitivity of the measurement you're going to make. You'll notice three jack inputs arranged in a vertical line on the bottom right. They are marked – from top to bottom – 10ADC, VΩmA and COM. The meter comes with a pair of leads, one black and one red, that fit into these jacks.

On the left side, you'll see a multipin transistor /hFE jack for testing transistors. You'll also see an On/Off button. Turn this on to activate the LED display. Measuring Voltage and Current. To measure current, switch the red lead to the 10 ADC jack and leave the black one in the COM jack.

Turn the dial to the 10 amp (10A) area, make sure the meter is on, touch the leads to the exposed circuit wires and note the reading. If it's below 0.2 amps, turn off the meter, place the red lead into the VmA jack and turn the dial one position counterclockwise to the 220m setting in the DC amp (DCA) area. Turn on the meter and take another reading. Continue turning the dial counterclockwise – all the way to 200 µ if necessary – to increase the accuracy of the reading. Measuring Resistance and Continuity.

When you measure resistance, the unit supplies a small current, so there must be no other current source. Check the circuit with the voltage function to make sure the meter reads 0. Insert the red lead in the VΩmA jack and the black lead in COM. Turn on the multimeter and move the selector to the 200 position in the ohm (Ω) area. Chappee oil boiler manual free download programs.

Before you take a measurement, touch the leads together and make sure the meter reads 0, indicating there is no resistance between the leads. Touch the leads to the exposed circuit wires and note the reading. If the reading is 1, turn the dial one position counterclockwise and try again. Keep turning the dial – all the way to 2000k if necessary – until you get a reading other than 1. You can use the multimeter to test the voltage drop across a diode so you can compare it to the diode's specifications and determine whether it's still good. Turn the dial to the diode section, which is at the 6 o'clock position next to the lowest setting in the ohm section. Insert the red lead into the VΩmA jack and the black lead into COM.

Turn on the meter. Touch the red lead to one terminal of the diode and the black lead to the other and note the reading, which is displayed in millivolts.

If the reading is 1, reverse the leads and try again.

• 7 FUNCTION DIGITAL MULTIMETER 69096 OPERATING INSTRUCTIONS Visit our Web site at REV 12a Copyright 2011 by Harbor Freight Tools. All rights reserved. © ® No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. • Safety Warnings and Precautions WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.

Warnings continued on page 3. SKU 69096 For replacement parts, please call 1-800-444-3353. • Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not operate properly. SKU 69096 For replacement parts, please call 1-800-444-3353. • Do not test voltage on AC circuits higher than 750 volts. Do not test voltage on DC circuits higher than 1000 volts.

Do not test current on circuits higher than 10 amps. SKU 69096 For replacement parts, please call 1-800-444-3353. • Measure DC conductors carrying up to 1000 VDC. Turn the Range Selector Switch to 1000 DCV setting. Follow the directions above under “AC Voltage Measurements”, only use the DC settings instead. SKU 69096 For replacement parts, please call 1-800-444-3353.

• Plug the red Test Lead into the VΩmA (Center) Jack. Plug the black Test Lead into the Com (Bottom) Jack. Switch the Multimeter ON. Connect the red probe to the anode of the diode and the black to the cathode. SKU 69096 For replacement parts, please call 1-800-444-3353.

• Pull battery/fuse out of unit and replace with the same. (9V battery or 500mA/250V fast-acting fuse) Replace cover and retighten screws. NOTE: No replacement parts are available for this tool.

SKU 69096 For replacement parts, please call 1-800-444-3353.

It is sold in Australia by as the T-Touch Tab. Proshivka 23 huawei ideos s7. It is sold exclusively by Telstra for use on the. It is the cheapest tablet in Australia, according to PC World 'the T-Touch Tab is effectively alone as an affordable, entry-level tablet that doesn't skimp on too many features'.